|
Download the MSDS in pdf
format |
|
Glaze-Ease
601 MSDS |
|
|
ADVANCED REPAIR TECHNOLOGY
MATERIAL SAFETY DATA SHEET
MSDS Product: Glaze-Ease 601
Manufacturer’s Name & Address:
Advanced Repair Technology
P.O. Box 510
Cherry Valley, NY 13317
607-264-9040Emergency Telephone:
800-424-9300 (24 hours) CHEM TREC
For Chemical Emergency Exposure, or Accident
|
|
Section I – Product Identification |
|
Chemical Name: SILICONIZED SEALANT
Product/Trade Name: Glaze-Ease 601
Chemical Family: Silicone Acrylic Blend
Synonyms: SILICONE/ACRYLIC
CAS Registry #: TRADE SECRET
Formula: N.A.
|
Hazard Designations |
HMIS |
NPFA |
| Health |
1 |
1 |
|
Flammability |
0 |
0 |
|
Reactivity |
0 |
0 |
|
Protective Equipment or Special Hazards |
0 |
0 |
|
0=Minimal 1=Slight
2=Moderate 3=Serious 4=Severe |
|
|
|
|
Section II – Hazardous
Ingredients/Identity Information |
|
Ingredients |
Percent |
TLV (Units |
|
None |
100 |
NE |
|
|
|
|
Section III – Physical/Chemical
Characteristics |
|
|
|
Boiling Point |
N.A. |
|
Freezing Point |
N.A. |
|
Melting Point |
N.A. |
|
Vapor Pressure |
NEGLIGIBLE.A. |
|
Vapor Density |
HEAVIER THAN AIR |
|
Solubility in Water |
SLIGHTLY SOLUBLE |
|
Specific Gravity |
13.1 LBS/GAL |
|
% Volatility by Volume: |
18% |
|
Evaporation Rate |
N.A. |
|
State |
Liquid |
|
Viscosity |
THIXOTROPIC PASTE |
|
Other Information |
N.A |
|
Appearance & Odor |
WHITE PASTE WITH LOW ODOR |
|
|
Section IV – Fire & Explosion Hazard
Data |
|
Flash point (Method used: PMCC): N.A.
Flammable Limits: NOT ESTABLISHED
Fire Extinguishing Media: ALL STANDARD
FIREFIGHTING AGENTS ARE SUITABLE. MATERIAL IS ESSENTIALLY
NON-FLAMMABLE.
Special Fire Fighting Procedures:
AS IN ANY FIRE, PREVENT HUMAN EXPOSURE TO FIRE,
SMOKE, FUMED OR PRODUCTS OF COMBUSTION. EVACUATE NON-ESSENTIAL
PERSONNEL FROM THE AREA. FIRE FIGHTERS
SHOULD WEAR FULL-FACE, SELF-CONTAINED BREATHING APPARATUS AND
IMPERVIOUS PROTECTIVE CLOTHING. USE STANDARD FIREFIGHTING
TECHNIQUES. CLOSED CONTAINERS MAY RUPTURE WHEN EXPOSED TO EXTREME
HEAT.
Autoignition Temperature: None available:
|
|
Section V – Health Hazard Data |
|
Threshold Limit Value: Unknown.
Health Hazards:
WARNING! MAY CAUSE MILD EYE IRRITATION. AVOID
CONTACT WITH SKIN, EYES, AND CLOTHING, DIRECT CONTACT WITH UNCURED
PRODUCT OR ITS VAPORS MAY CAUSE IRRITATION. INGESTION OF THE
MATERIAL MAY PRODUCE SOME ABDOMINAL PAIN AND DIARRHEA.
Emergency & First Aid Procedures:
INGESTION: IF SWALLOWED, DO NOT INDUCE VOMITING. IF
VOMITING OCCURS, GIVE MORE FLUID. HAVE A PHYSICIAN DETERMINE IF
CONDITION OF PATIENT WILL PERMIT EVACUATION OF STOMACH, OR INDUCTION
OF VOMITING. DO NOT GIVE FLUID TO AN UNCONSCIOUS PERSON.
SKIN CONTACT: FLUSH ALL AFFECTED AREAS WITH WATER.
REMOVE ANY CONTAMINATED CLOTHING OR SHOES. SEEK MEDICAL ATTENTION IF
SKIN IRRITATION OCCURS. WASH OR DISCARD CLOTHING.
EYE CONTACT: IMMEDIATELY FLUSH THE EYE WITH LARGE
AMOUNTS OF WATER OF WATER FOR AT LEAST 15 MINUTES. HOLD EYELIDS
APART TO ASSURE A THOROUGH FLUSHING. DO NOT ATTEMPT TO NEUTRALIZE
ANY CHEMICAL. OBTAIN MEDICAL ASSISTANCE AS SOON AS POSSIBLE. FLUSH
AN ADDITIONAL 15 MINUTES IF MEDICAL ATTENTION IS NOT AVAILABLE.
Toxicological Data: None Established
|
|
Section VI – Reactivity Data |
|
Stability: Stable
Condition to Avoid: DO NOT ALLOW TO FREEZE.
Incompatibility: None Known.
Hazardous Combustion or Decomposition Products:
Carbon dioxide and monoxide.
Hazardous Polymerization: Will not occur
|
|
Section VII – Spill, Leak, and Waste
Disposal Procedures |
|
Waste Disposal and Spill Control Methods
:
CONDUCT IN ACCORDANCE WITH OSHA 29 CFR 1910. FOLLOW
GOOD INDUSTRIAL HYGIENE PRACTICES. (SEE SEC. VIII). WEAR PROTECTIVE
CLOTHING. WIPE UP EXCESS WITH PAPER OR CLOTH TOWELS, AND PLACE IN A
CHEMICAL WASTE DRUM FOR DISPOSAL. WASH UP AREA WITH DETERGENT AND
WATER, FLUSH WITH WATER. MATERIAL THAT CANNOT BE USED SHOULD
BE DISPOSED OF IN ANY TOWN DUMPING FACILITY. DISPOSE OF EMPTY
CONTAINERS ACCORDING TO ANY APPLICABLE REGULATIONS UNDER THE
RESOURCE CONSERVATION AND RECOVERY ACT. (B)
|
|
Section VIII – Special Protection
Information |
|
Respiratory Protection: IF USE CONDITIONS GENERATE VAPOR, THE
MATERIAL SHOULD BE HANDLED IN A WELL-VENTILATED AREA. DO NOT BREATHE
VAPORS AS IRRITATION MAY RESULT.
Ventilation: If use generates vapor, general
mechanical ventilation is recommended in a closed area.
Personal Protection: Safety glasses and
approved plastic film/rubber gloves are suggested.
Work Practices/Hygiene: Practice reasonable
care and cleanliness and avoid prolonged contact with skin and eyes.
|
|
Section IX – Special Precautions |
|
Handling and storage: Avoid contact with skin and eyes. Store
in a cool, dry area with good ventilation. Do not allow to freeze.
Other Precautions: Contact lens wearers should
take appropriate precaution. Avoid high temperature conditions.
Precautionary Labeling: None required
|
|
Section X – Additional Information |
N.A.
|
|
Section XI – Requirements of
Transportation |
|
Proper Shipping Name: RESIN EMULSION
Hazard Class: None
UN/NA #: None
Special Provisions: None
Hazard Name: NOT A HAZARDOUS MATERIAL
Label/Placard: None
EPA RQ N: .00 Pounds or .00 Kilos |
|
Download the MSDS in pdf
format |
|
|
